Ipmitool: Difference between revisions
From Leo's Notes
This page was last edited on 18 December 2021, at 23:50.
No edit summary |
|||
| Line 13: | Line 13: | ||
==Usage== | ==Usage== | ||
{| class="wikitable" | |||
!Task | |||
{{Highlight | !Command | ||
| code = # | |- | ||
# | |Print the iDRAC network settings | ||
# | |<code>ipmitool lan print</code> | ||
# | |- | ||
|Set the iDRAC network settings | |||
|{{Highlight | |||
| code = # ipmitool lan set 1 ipsrc static | |||
# ipmitool lan set 1 ipaddr 10.1.1.21 | |||
# ipmitool lan set 1 netmask 255.255.255.0 | |||
# ipmitool lan set 1 defgw ipaddr 10.1.1.1 | |||
| lang = terminal | | lang = terminal | ||
}} | }} | ||
|- | |||
|View system event logs | |||
{{Highlight | |<code>ipmitool sel elist</code> | ||
|- | |||
|Clear system event logs / amber light | |||
|<code>ipmitool sel clear</code> | |||
|- | |||
|Powercycle a machine | |||
|<code>ipmitool -U ''username'' -f ''passwd.txt'' -I lanplus -H ''hostname'' chassis power cycle</code> | |||
|- | |||
|Reset iDRAC account password | |||
|{{Highlight | |||
| code = # ipmitool user list 1 | | code = # ipmitool user list 1 | ||
ID Name Callin Link Auth IPMI Msg Channel Priv Limit | ID Name Callin Link Auth IPMI Msg Channel Priv Limit | ||
| Line 49: | Line 64: | ||
| lang = terminal | | lang = terminal | ||
}} | }} | ||
|} | |||
== Tasks == | |||
===View System Event Logs=== | ===View System Event Logs=== | ||
| Line 68: | Line 86: | ||
| lang = terminal | | lang = terminal | ||
}} | }} | ||
===Polling Data=== | ===Polling Data=== | ||
Revision as of 23:50, 18 December 2021
ipmitool is a utility to fetch information from devices that support the Intelligent Platform Management Interface (IPMI). This includes servers such as the HP Proliant DL380 G6 which I have at home or practically all Dell servers.
The project can be found at:
Installation
Clone the repository from https://github.com/ipmitool/ipmitool, then run autoconf, ./configure, make.
A docker image containing this binary can be found at:
Usage
| Task | Command |
|---|---|
| Print the iDRAC network settings | ipmitool lan print
|
| Set the iDRAC network settings | # ipmitool lan set 1 ipsrc static
# ipmitool lan set 1 ipaddr 10.1.1.21
# ipmitool lan set 1 netmask 255.255.255.0
# ipmitool lan set 1 defgw ipaddr 10.1.1.1
|
| View system event logs | ipmitool sel elist
|
| Clear system event logs / amber light | ipmitool sel clear
|
| Powercycle a machine | ipmitool -U username -f passwd.txt -I lanplus -H hostname chassis power cycle
|
| Reset iDRAC account password | # ipmitool user list 1
ID Name Callin Link Auth IPMI Msg Channel Priv Limit
1 true false false NO ACCESS
2 root true true true ADMINISTRATOR
3 true false false NO ACCESS
4 true false false NO ACCESS
5 true false false NO ACCESS
6 true false false NO ACCESS
7 true false false NO ACCESS
8 true false false NO ACCESS
9 true false false NO ACCESS
10 true false false NO ACCESS
11 true false false NO ACCESS
12 true false false NO ACCESS
13 true false false NO ACCESS
14 true false false NO ACCESS
15 true false false NO ACCESS
16 true false false NO ACCESS
# ipmitool user set password 2
Password for user 2:
Password for user 2:
|
Tasks
View System Event Logs
Use ipmitool sel elist to show logs.
# ipmitool sel elist
1 | 08/24/2006 | 14:05:17 | Event Logging Disabled SEL | Log area reset/cleared | Asserted
2 | 12/11/2008 | 03:21:50 | Memory ECC Corr Err | Correctable ECC (Correctable ECC | Bank 1DIMM B) | Asserted
3 | Pre-Init |0000000011| Physical Security Intrusion | General Chassis intrusion | Asserted
4 | Pre-Init |0000000017| Physical Security Intrusion | General Chassis intrusion | Deasserted
5 | Pre-Init |0000000011| Physical Security Intrusion | General Chassis intrusion | Asserted
6 | Pre-Init |0000000016| Physical Security Intrusion | General Chassis intrusion | Deasserted
7 | Pre-Init |0000000011| Physical Security Intrusion | General Chassis intrusion | Asserted
8 | Pre-Init |0000000016| Physical Security Intrusion | General Chassis intrusion | Deasserted
9 | 06/11/2020 | 08:40:21 | Voltage CMOS Battery | Lower Critical going low | Asserted | Reading 2.57 < Threshold 2.64 Volts
a | 06/11/2020 | 08:41:41 | Voltage CMOS Battery | Lower Critical going low | Deasserted | Reading 2.73 < Threshold 2.64 Volts
b | 06/13/2020 | 19:01:06 | Voltage CMOS Battery | Lower Critical going low | Asserted | Reading 2.63 < Threshold 2.64 Volts
c | 06/13/2020 | 19:01:11 | Voltage CMOS Battery | Lower Critical going low | Deasserted | Reading 2.68 < Threshold 2.64 Volts
Polling Data
Poll the data from iLO by running ipmitool. An example output is given below.
/tmp # ./ipmitool -I lanplus -H X.X.X.X -U Administrator -P XXXXXXXXXX sensor
Unable to Get Channel Cipher Suites
UID Light | 0x0 | discrete | 0x0080| na | na | na | na | na | na
Sys. Health LED | 0x0 | discrete | 0x0080| na | na | na | na | na | na
Power Supply 1 | 85 | Watts | ok | na | na | na | na | na | na
Power Supply 2 | 95 | Watts | ok | na | na | na | na | na | na
Power Supplies | 0x0 | discrete | 0x0180| na | na | na | na | na | na
Fan 1 | 13.720 | percent | ok | na | na | na | na | na | na
Fan 2 | 13.720 | percent | ok | na | na | na | na | na | na
Fan 3 | 22.736 | percent | ok | na | na | na | na | na | na
Fan 4 | 27.048 | percent | ok | na | na | na | na | na | na
Fan 5 | 22.736 | percent | ok | na | na | na | na | na | na
Fan 6 | 13.720 | percent | ok | na | na | na | na | na | na
Fans | 0x0 | discrete | 0x0180| na | na | na | na | na | na
Temp 1 | 19.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 39.000 | 41.000 | 45.000
Temp 2 | 40.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 82.000 | 83.000
Temp 3 | 40.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 82.000 | 83.000
Temp 4 | 37.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 87.000 | 92.000
Temp 5 | 39.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 87.000 | 92.000
Temp 6 | 44.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 87.000 | 92.000
Temp 7 | 42.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 87.000 | 92.000
Temp 8 | 48.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 90.000 | 95.000
Temp 9 | 42.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 65.000 | 70.000
Temp 10 | 48.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 90.000 | 95.000
Temp 11 | 40.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 12 | 49.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 90.000 | 95.000
Temp 13 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 14 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 15 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 16 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 17 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 18 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 19 | 24.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 20 | 36.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 21 | 34.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 80.000 | 85.000
Temp 22 | 32.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 80.000 | 85.000
Temp 23 | 43.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 77.000 | 82.000
Temp 24 | 38.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 25 | 39.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 26 | 38.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 27 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 28 | na | | na | 0.000 | 0.000 | 0.000 | 0.000 | 70.000 | 75.000
Temp 29 | 35.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 60.000 | 65.000
Temp 30 | 77.000 | degrees C | ok | 0.000 | 0.000 | 0.000 | 0.000 | 110.000 | 115.000
Memory | 0x0 | discrete | 0x4080| na | na | na | na | na | na
Power Meter | 188 | Watts | ok | na | na | na | na | na | na
The data can be parsed then pushed into a logging server.
Troubleshooting
$ autoconf
configure.ac:8: error: possibly undefined macro: AM_INIT_AUTOMAKE
If this token and others are legitimate, please use m4_pattern_allow.
See the Autoconf documentation.
configure.ac:9: error: possibly undefined macro: AM_CONFIG_HEADER
configure.ac:38: error: possibly undefined macro: AM_PROG_LIBTOOL
Fix this by running:
$ autoreconf -i