Clear RAID Signatures on Linux: Difference between revisions
From Leo's Notes
This page was last edited on 1 September 2019, at 06:21.
m Text replacement - "Category:Linux{{Navbox Linux}}" to "{{Navbox Linux}}Category:Linux" |
|||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
You may need to clear RAID | You may need to clear RAID configs left on hard drives when trying to install Linux on a disk from a RAID array. | ||
Installers such as Anaconda will not list drives with these RAID signatures. If you're unable to find a disk in Anaconda, clear the configs using the steps below. | |||
== Listing Devices == | == Listing Devices == | ||
| Line 8: | Line 10: | ||
== Removing Devices == | == Removing Devices == | ||
Use any one of these methods to clear the RAID configs from the disk. The bulletproof method is to use {{code|dd}}. | |||
Remove using {{code|dmsetup}}: | Remove using {{code|dmsetup}}: | ||
{{highlight|lang=terminal|code= | {{highlight|lang=terminal|code= | ||
dmsetup remove /dev/mapper/ddfs1_backups | # dmsetup remove /dev/mapper/ddfs1_backups | ||
}} | }} | ||
| Line 26: | Line 29: | ||
Remove by overwriting the raid configs using {{code|dd}}. The location the configs are located at the last 1024 sectors of the disk. | Remove by overwriting the raid configs using {{code|dd}}. The location the configs are located at the last 1024 sectors of the disk. | ||
{{highlight|lang=terminal|code= | {{highlight|lang=terminal|code= | ||
dd if=/dev/zero of=/dev/sda bs=512 seek=$(( $(blockdev --getsz /dev/sda) - 1024 )) count=1024 | # dd if=/dev/zero of=/dev/sda bs=512 seek=$(( $(blockdev --getsz /dev/sda) - 1024 )) count=1024 | ||
}} | }} | ||
[[Category:Linux]] | After removing the configs, verify using {{code|dmraid -r}}. | ||
== See Also == | |||
* http://serverfault.com/questions/488346/removing-raid-metadata-from-drives | |||
{{Navbox Linux}}[[Category:Linux]] | |||
Latest revision as of 06:21, 1 September 2019
You may need to clear RAID configs left on hard drives when trying to install Linux on a disk from a RAID array.
Installers such as Anaconda will not list drives with these RAID signatures. If you're unable to find a disk in Anaconda, clear the configs using the steps below.
Listing Devices
# dmraid -r
/dev/sda: ddf1, ".ddf1_backups", GROUP, ok, 3904294912 sectors, data@ 0
Removing Devices
Use any one of these methods to clear the RAID configs from the disk. The bulletproof method is to use dd.
Remove using dmsetup:
# dmsetup remove /dev/mapper/ddfs1_backups
Remove using dmraid:
# dmraid -r -E /dev/sda
Do you really want to erase "ddf1" ondisk metadata on /dev/sda ? [y/n] :y
ERROR: ddf1: seeking device "/dev/sda" to 1024204253954048
ERROR: writing metadata to /dev/sda, offset 2000398933504 sectors, size 0 bytes returned 0
ERROR: erasing ondisk metadata on /dev/sda
Remove by overwriting the raid configs using dd. The location the configs are located at the last 1024 sectors of the disk.
# dd if=/dev/zero of=/dev/sda bs=512 seek=$(( $(blockdev --getsz /dev/sda) - 1024 )) count=1024
After removing the configs, verify using dmraid -r.
See Also