DRBD: Difference between revisions

From Leo's Notes
This page was last edited on 31 March 2015, at 20:24.
← Older editNewer edit →
VisualWikitext
Line 60: Line 60:


Configure the DRBD config in /etc/drbd.d/*conf. You may want to disable the survey.
Configure the DRBD config in /etc/drbd.d/*conf. You may want to disable the survey.
Configure DRBD by creating a file in /etc/drbd.d/mysql.res
Configure DRBD by creating a file in /etc/drbd.d/mysql.res with:
<syntaxhighlight lang="text">
<syntaxhighlight lang="text">
resource mysql {
resource mysql {
Line 71: Line 71:
meta-disk internal;
meta-disk internal;


on node1 {
on $hostname {
address 172.20.10.10:7700;
address 172.20.10.10:7700;
}
}


on node2 {
on $hostname {
address 172.20.10.9:7700;
address 172.20.10.9:7700;
}
}
Line 81: Line 81:
</syntaxhighlight>
</syntaxhighlight>


If you get an error like:
Be sure to rename the hostnames so that it matches the actual machine's hostname. Otherwise, you will get an error like:
  'mysql' not defined in your config (for this host).
  'mysql' not defined in your config (for this host).
You are probably doing something wrong.


== See Also ==
== See Also ==

Revision as of 20:24, 31 March 2015

DRBD (Distributed Replicated Block Device) is a virtual block device that is distributed across two or more machines.

Installation

On a clean installation of RHEL 7 or equivalent, run updates, and ensure that you have NTP and a recent kernel installed.

From ElRepo

Get the DRBD packages from ELRepo: 

rpm -Uvh http://www.elrepo.org/elrepo-release-7.0-2.el7.elrepo.noarch.rpm
yum install drbd84-utils kmod-drbd84

From Source

Install prerequisites: 

yum install gcc flex make autoconf m4

Get the source from their git repository. Releases from tarballs may fail depending on which kernel version you're using. 

git clone git://git.drbd.org/drbd-8.4.git
cd drbd-8.4
make
make install

The make install should have loaded the module and you can verify this: 

lsmod | grep drbd

If it isn't loaded, load it using modprobe 

modprobe drbd

Compile the userspace utilities: 

git clone git://git.drbd.org/drbd-utils.git
cd drbd-utils
./aclocal.sh
./configure --prefix=/usr --localstatedir=/var --sysconfdir=/etc
make
make install

Note: I got errors about man pages not being found. Ugh.


Configuration

This section will configure DRBD for use in a redundant MySQL setup.

DRBD syncs volumes. If you did not configure a partition or have a separate disk to mirror, you can create a file volume instead. 

mkdir /var/drbd
cd /var/drbd

# Create a 50GB volume
dd if=/dev/zero of=data_volume.dat bs=1024 count=52428800

# Create a partition
fdisk data_volume.dat

# Create a device
losetup /dev/loop0 /var/drbd/data_volume.dat
kpartx -v -a /var/drbd/data_volume.dat
ls /dev/mapper/

mkdir -p /mnt/drbd
echo "/dev/drbd0 /mnt/drbd ext4 noauto 0 0 " >>  /etc/fstab

Configure the DRBD config in /etc/drbd.d/*conf. You may want to disable the survey. Configure DRBD by creating a file in /etc/drbd.d/mysql.res with: 

resource mysql {
	disk {
		on-io-error detach;
	}

	device    /dev/drbd0;
	disk      /dev/loop0;
	meta-disk internal;

	on $hostname {
		address 172.20.10.10:7700;
	}

	on $hostname {
		address 172.20.10.9:7700;
	}
}

Be sure to rename the hostnames so that it matches the actual machine's hostname. Otherwise, you will get an error like: 

'mysql' not defined in your config (for this host).

See Also

Various Linux Notes
Linux Tools and Utilites
Package Management
Linux Distributions
Networking
Containers