Tapo C200: Difference between revisions

From Leo's Notes
This page was last edited on 27 November 2022, at 06:57.
No edit summary
No edit summary
Line 1: Line 1:
The TP-Link Tapo C200 is a 1080p IP camera that can tilt and pan. The camera supports RTSP out of the box.
The TP-Link Tapo C200 is a 1080p IP camera that can tilt and pan. The camera supports RTSP out of the box.


== Serial ==
== Serial console ==
Based on the information from https://drmnsamoliu.github.io/shell.html
Based on the information from https://drmnsamoliu.github.io/shell.html


Line 97: Line 97:
}}
}}


=== Working with the shell ===
Get <code>/proc</code> mounted using <code>mount -t proc none /proc</code>
=== Root password ===
The root password on this firmware version has changed and is no longer 'slprealtek' as discovered by kubik369 and documented on the Tapo C200 research site. The root hash is now set to:
{{Highlight
| code = root:$1$IjsWXCH9$z2Woc0uNFN4a7bZM7SGCF.:0:0:root:/root:/bin/ash
| lang = text
}}


== See also ==
== See also ==

Revision as of 06:57, 27 November 2022

The TP-Link Tapo C200 is a 1080p IP camera that can tilt and pan. The camera supports RTSP out of the box.

Serial console

Based on the information from https://drmnsamoliu.github.io/shell.html

Serial console can be accessed by wiring a USB UART to the test pads on the main board. Note that the TX/RX appears to be at 3.3v levels, so take care to use an appropriate UART device or a logic level shifter.

Pin Function
TP9 to UART RX (via 3.3v level shifter)
TP10 to UART TX (via 3.3v level shifter)
TP11 GND

You should see some boot messages when the device is powered on. Enter slp when you see the second Autobooting in 1 seconds message to enter the U-Boot menu.

U-Boot 2014.01-v1.2 (Aug 25 2021 - 12:36:20)

Board: IPCAM RTS3903 CPU: 500M :rx5281 prid=0xdc02
force spi nor mode
DRAM:  64 MiB @ 1066 MHz
Skipping flash_init
Flash: 0 Bytes
SF: Unsupported flash IDs: manuf 20, jedec 4017, ext_jedec 0000
flash status is 0, 2, 0
SF: Detected unknown with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Using default environment

Autobooting in 1 seconds
set watchdog, resetting...

U-Boot 2014.01-v1.2 (Jun 27 2022 - 09:04:38)

Board: IPCAM RTS3903 CPU: 500M :rx5281 prid=0xdc02
force spi nor mode
DRAM:  64 MiB @ 1066 MHz
manuf 20, jedec 4017, ext_jedec 0000
flash status is 0, 2, 0
SF: Detected unknown with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Flash: 0 Bytes
manuf 20, jedec 4017, ext_jedec 8204
flash status is 0, 2, 0
SF: Detected unknown with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   Realtek PCIe GBE Family Controller mcfg = 0024
new_ethaddr = 00:00:00:00:00:00
r8168#0
VF: validateLocalFirmware: copying flash to 0x82000000
manuf 20, jedec 4017, ext_jedec 0000
flash status is 0, 2, 0
SF: Detected unknown with page size 256 Bytes, erase size 64 KiB, total 8 MiB
SF: 8388608 bytes @ 0x0 Read: OK
VF: validateLocalFirmware: ret=0(82fb7de0)
VF: validateLocalFirmware: validate local firmware...
TP Header at 82070000
Autobooting in 1 seconds  <-- At this point, type 'slp'
rlxboot#

On the latest firmware as of November 2022, these are the settings that are set on my unit. Note the address to the kernel is at 0x70000 rather than 0x60000 as documented by the Tapo C200 research docs.

rlxboot# printenv
addmisc=setenv bootargs ${bootargs}console=ttyS0,${baudrate}panic=1
baudrate=57600
bootaddr=(0xBC000000 + 0x120000)
bootargs=console=ttyS1,57600 root=/dev/mtdblock6 spdev=/dev/mtdblock7 rts-quadspi.channels=dual
bootcmd=sf probe;sf read 0x82000000 0x70000 0x300000;bootm 0x82000000 
bootdelay=1
bootfile=/vmlinux.img
ethact=r8168#0
ethaddr=00:00:00:00:00:00
load=tftp 80500000 ${u-boot}
loadaddr=0x80100000
stderr=serial
stdin=serial
stdout=serial

Environment size: 477/131068 bytes

To boot into single user mode, tack on init=/bin/sh to the bootargs variable and run the bootcmd commands:

# setenv bootargs ${bootargs} init=/bin/sh
# sf probe
# sf read 0x82000000 0x70000 0x300000
# bootm 0x82000000

Working with the shell

Get /proc mounted using mount -t proc none /proc

Root password

The root password on this firmware version has changed and is no longer 'slprealtek' as discovered by kubik369 and documented on the Tapo C200 research site. The root hash is now set to:

root:$1$IjsWXCH9$z2Woc0uNFN4a7bZM7SGCF.:0:0:root:/root:/bin/ash

See also