SVN: Difference between revisions

From Leo's Notes
This page was last edited on 24 February 2017, at 19:14.
← Older editNewer edit →
VisualWikitext
m Text replacement - "<code>" to "{{code|"
m Text replacement - "</code>" to "}}"
Line 6: Line 6:
To back up a specific range of revisions:
To back up a specific range of revisions:
  svnadmin dump /path/to/repository -r startRev:endRev > backup.dump
  svnadmin dump /path/to/repository -r startRev:endRev > backup.dump
where {{code|startRev</code> is the starting revision number and {{code|endRev</code> the ending revision number. You may replace {{code|endRev</code> with {{code|HEAD</code> to specify the most recent revision.
where {{code|startRev}} is the starting revision number and {{code|endRev}} the ending revision number. You may replace {{code|endRev}} with {{code|HEAD}} to specify the most recent revision.


== Restore Repository ==
== Restore Repository ==
Line 17: Line 17:
  service svnsersve start
  service svnsersve start


To configure {{code|svnserve</code>, you will need two files in your repository's {{code|conf/</code> directory:
To configure {{code|svnserve}}, you will need two files in your repository's {{code|conf/}} directory:


{{code|svnserve.conf:</code>
{{code|svnserve.conf:}}
<syntaxhighlight lang="text" line start="1" enclose="div">
<syntaxhighlight lang="text" line start="1" enclose="div">
[general]
[general]
Line 43: Line 43:
</syntaxhighlight>
</syntaxhighlight>


{{code|passwd:</code> (as defined above in {{code|password-db</code>)
{{code|passwd:}} (as defined above in {{code|password-db}})


<syntaxhighlight lang="text" line start="1" enclose="div">
<syntaxhighlight lang="text" line start="1" enclose="div">
Line 54: Line 54:
  <nowiki>svn://server/<path_to_repository></nowiki>
  <nowiki>svn://server/<path_to_repository></nowiki>


For example, if my repository was placed in {{code|/home/leo/repository/project_v1</code>, you should be able to checkout and commit at:
For example, if my repository was placed in {{code|/home/leo/repository/project_v1}}, you should be able to checkout and commit at:
  <nowiki>svn://server/home/leo/repository/project_v1</nowiki>
  <nowiki>svn://server/home/leo/repository/project_v1</nowiki>


If you have defined your {{code|svnserve.conf</code> properly, you will be prompted for a username/password.
If you have defined your {{code|svnserve.conf}} properly, you will be prompted for a username/password.




Revision as of 19:14, 24 February 2017

Backup Repository

Backing up the entire repository from beginning of time to the most recent revision: 

svnadmin dump /path/to/repository > backup.dump

To back up a specific range of revisions: 

svnadmin dump /path/to/repository -r startRev:endRev > backup.dump

where startRev is the starting revision number and endRev the ending revision number. You may replace endRev with HEAD to specify the most recent revision.

Restore Repository

svnadmin create /path/to/repository
svnadmin load /path/to/repository < backup.dump

Setting up svnserve

To set up svnserve under CentOS/ScientificLinux, run: 

yum install subversion
service svnsersve start

To configure svnserve, you will need two files in your repository's conf/ directory:

svnserve.conf: 

[general]
### These options control access to the repository for unauthenticated
### and authenticated users.  Valid values are "write", "read",
### and "none".  The sample settings below are the defaults.
anon-access = none
auth-access = write

### The password-db option controls the location of the password
### database file.  Unless you specify a path starting with a /,
### the file's location is relative to the directory containing
### this configuration file.
### If SASL is enabled (see below), this file will NOT be used.
### Uncomment the line below to use the default password file.
password-db = passwd

### This option specifies the authentication realm of the repository.
### If two repositories have the same authentication realm, they should
### have the same password database, and vice versa.  The default realm
### is repository's uuid.
realm = Project Version 1.0 Repository

passwd: (as defined above in password-db) 

[users]
leo = meinpasswort

Accessing Your Repository

You can now access your repository at: 

svn://server/<path_to_repository>

For example, if my repository was placed in /home/leo/repository/project_v1, you should be able to checkout and commit at: 

svn://server/home/leo/repository/project_v1

If you have defined your svnserve.conf properly, you will be prompted for a username/password.

Linux