IBM Spectrum Archive: Difference between revisions
m →Tapes |
|||
| Line 114: | Line 114: | ||
=== Show Tiered Files === | === Show Tiered Files === | ||
A file is '''migrated''' when the file contents have been copied to one or more tape and its original GPFS location is turned into a file stub. All files that are only stored on GPFS are '''resident'''. Files that are in the process of being migrated, where the data has been copied to the LTFSEE storage and is waiting to be copied to tape are '''pre-migrated'''. | |||
File statuses can be viewed with {{code|ltfsee info files -f filepath}}. The location (or locations if multiple copies were made) is given as the tape ID and library name under each file entry. | |||
{{highlight|lang=terminal|code= | {{highlight|lang=terminal|code= | ||
# ltfsee info files -f /tiered/ewang_scratch/xuexu/dbgap_UK_OTTO/SRR302* | # ltfsee info files -f /tiered/ewang_scratch/xuexu/dbgap_UK_OTTO/SRR302* | ||
Revision as of 20:08, 12 August 2019
Usage
Use the ltfsee command to interact with the LTFS system. Other binaries related to LTFS can be found at /opt/ibm/ltfsee/bin/.
LTFS Library Status
[root@ltfs ~]# ltfsee status
Ctrl Node MD MMM Library
172.26.3.249 Active Active T_ARCH
Tapes
List Tape Drives
To show all tape drives:
[root@ltfs ~]# ltfsee info drives
Drive S/N Status Type Role Library Address Node ID Tape Node Group
0007807A4B In use LTO8 mrg T_ARCH 260 4 T00031L8 G0
0007807A0B Mounted LTO8 mrg T_ARCH 261 4 - G0
000780765B In use LTO8 mrg T_ARCH 262 4 T00054L8 G0
If drives are in use, you can list all in-progress jobs to see what task is using the drive.
[root@ltfs ~]# ltfsee info jobs
Job Type Status Idle(sec) Scan ID Tape Pool Library Node File Name or inode
Reclaim(Source) In-progress 573811 2944737025 T00031L8 TIERED1 T_ARCH 4 -
Reclaim(Target) In-progress 573683 2944737281 T00054L8 TIERED1 T_ARCH 4 -
Validate Unscheduled 4469 1602429441 T00054L8 TIERED1 T_ARCH - -
List Tape Cartridges
To show all tapes in the library, run ltfsee info tapes. Common tape status codes are:
| Status Code | Description |
|---|---|
| Critical | The Critical status indicates that an attempt to write to this cartridge failed.
To avoid data loss, recover the data on this cartridge by using the ltfsee recover command, then discard this cartridge. |
| Error | The Error status indicates that the cartridge has an error and cannot be recovered.
This cartridge cannot be used with the IBM Spectrum Archive Enterprise Edition. |
| Invalid | The Invalid status indicates that the cartridge is inconsistent with the LTFS format.
To check and repair this tape before you add it to a tape storage pool, use the ltfsee pool add command with the check option. |
| Unavailable | The Unavailable status indicates that the cartridge is not available in the IBM Spectrum Archive Enterprise Edition system.
Tapes that are newly inserted into the tape library have an Unavailable status. To recall files from a tape with this status, first import the tape by using the ltfsee import command. To add a tape with this status to the IBM Spectrum Archive Enterprise Edition system: First, move the tape to a home slot by using the ltfsee tape move command. Then, add the tape to a tape storage pool by using the ltfsee pool command. |
| Valid | The Valid status indicates that the cartridge is valid. |
Other tape statuses and descriptions can be found at:
[root@ltfs ~]# ltfsee info tapes
Tape ID Status Type Capacity(GiB) Used(GiB) Free(GiB) Reclaimable(GiB) Pool Library Address Drive Appendable
T00000L8 Valid L8 10907 0 10907 0 TIERED1 T_ARCH 1161 - yes
T00001L8 Valid L8 10907 0 10907 0 TIERED1 T_ARCH 1160 - yes
T00003L8 Valid L8 10907 0 10907 0 TIERED1 T_ARCH 1158 - yes
T00004L8 Valid L8 10907 0 10907 0 TIERED1 T_ARCH 1157 - yes
Managing Tape Cartridges
To add tapes to a particular pool, use ltfsee pool add -p pool -t tape ...:
[root@ltfs ~]# ltfsee pool add -p TIERED2 -t T00099L8
GLESL042I(00894): Adding tape T00099L8 to storage pool TIERED2.
Added tape T00099L8 to pool TIERED2 successfully.
To remove tapes from a particular pool, use ltfsee pool remove -p pool -t tape .... This can only be done if the data on the tape is recovered using the ltfsee recover command. Files on the tape to be removed has to be in the "resident" state before LTFS allows you to remove the tape.
[root@ltfs ~]# ltfsee pool remove -p TIERED1 -t T00030L8
GLESL043I(01134): Removing tape T00030L8 from storage pool TIERED1.
Removed tape T00030L8 from pool TIERED1 successfully.
If a tape is in a drive, you can move it back to its homeslot using ltfsee tape move homeslot -t tape -p pool. Alternatively, use ieslot to move it to the IO slot of the tape library for extraction.
# ltfsee tape move homeslot -t T00037L8 -p TIERED1
GLESL373I(00890): Moving tape T00037L8.
Tape T00037L8 is unmounted because it is inserted into the drive.
Tape T00037L8 is moved successfully.
LTFS Information
ltfsee info pools shows all pools.
Pool Name Total(TiB) Used(TiB) Free(TiB) Reclaimable(TiB) Tapes Type Library Node Group
TIERED1 644.3 84.6 559.7 0.0 61 LTO T_ARCH G0
TIERED2 638.9 80.8 558.1 0.0 61 LTO T_ARCH G0
ltfsee info libraries shows all libraries with LTFS.
[root@ltfs ~]# ltfsee info libraries
Library Name Status Model Serial Number Ctrl Node
T_ARCH Active 03584L32 0000078BA6130402 172.26.3.249
Show Tiered Files
A file is migrated when the file contents have been copied to one or more tape and its original GPFS location is turned into a file stub. All files that are only stored on GPFS are resident. Files that are in the process of being migrated, where the data has been copied to the LTFSEE storage and is waiting to be copied to tape are pre-migrated.
File statuses can be viewed with ltfsee info files -f filepath. The location (or locations if multiple copies were made) is given as the tape ID and library name under each file entry.
# ltfsee info files -f /tiered/ewang_scratch/xuexu/dbgap_UK_OTTO/SRR302*
Name: /tiered/ewang_scratch/xuexu/dbgap_UK_OTTO/SRR3021220_2.fastq
Tape id:- Status: resident
Name: /tiered/ewang_scratch/xuexu/dbgap_UK_OTTO/SRR3021242_1.fastq
Tape id:T00042L8@T_ARCH:T00102L8@T_ARCH Status: migrated
Name: /tiered/ewang_scratch/xuexu/dbgap_UK_OTTO/SRR3021288_1.fastq
Tape id:T00055L8@T_ARCH:T00107L8@T_ARCH Status: migrated
Side Notes on Migrated Files
Migrated files will have a stub file with zero size. To count sizes withdu, you need to use --apparent-size Eg.
[root@node001 xuexu]# du -sh dbgap_UK_OTTO
23T dbgap_UK_OTTO
[root@node001 xuexu]# du -sh --apparent-size dbgap_UK_OTTO
35T dbgap_UK_OTTO
[root@node001 dbgap_UK_OTTO]# du SRR3021288_2.fastq
0 SRR3021288_2.fastq
[root@node001 dbgap_UK_OTTO]# du -sh --apparent-size SRR3021288_2.fastq
15G SRR3021288_2.fastq
To find all files that are stored on a particular tape, the easiest way is to look at the .schema metadata files for the library stored in /tiered/.ltfsee/meta/$library-id/volume_cache/*.schema.
For example, files stored on tape T00037L8 can be found this way:
# cd /tiered/.ltfsee/meta/0000078BA6130402/volume_cache
# grep gpfs.path -A 1 T00037L8.schema | grep value
<value>/tiered/ewang/xuexu/TCGA_bam_germline_12_4/f02e8ee1-349f-42ff-9ed9-ac37435901fa/cdb2f568f3cbdff5a9cd2edd692613bb_gdc_realn.bam</value>
<value>/tiered/ewang/xuexu/TCGA_bam_germline_12_4/TCGA-A2-A0D2_1.fastq</value>
...
Movement Policies
File movements are defined and applied by mmapplypolicy. A scheduled job invoking mmapplypolicy daily can be used to tier files on a regular basis.
The primary policy is on the LTFS server located at /mmpolicies/mmpolicyLATEST.txt and are applied with a daily cronjob that invokes:
# mmapplypolicy /dev/gpfs1 -P /mmpolicies/mmpolicyLATEST.txt >/dev/null 2>&1
# mmapplypolicy /dev/gpfs0 -P /mmpolicies/mmpolicyLATEST.txt >/dev/null 2>&1
The policy file contains the rules that govern which files are moved off to tape. LTFS/GPFS related files, specific filesystem logs, Space Manager(?) should not be migrated.
To prevent tiering of small amounts of data which could cause wear loading/unloading tape excessively, tiering can also be configured to happen only if filesystem usage exceeds 90% and will attempt to lower filesystem usage down to 80% as defined by the THRESHOLD values. Small files can also be ignored with the FILE_SIZE condition.
define(user_exclude_list,(PATH_NAME LIKE '/ibm/gpfs/.ltfsee/%' OR PATH_NAME LIKE'/ibm/gpfs/.SpaceMan/%' OR NAME LIKE 'dsmerror.log'))
define(user_include_list,(PATH_NAME LIKE '/tiered/%'))
define(is_premigrated,(MISC_ATTRIBUTES LIKE '%M%' AND MISC_ATTRIBUTES NOT LIKE'%V%'))
define(is_migrated,(MISC_ATTRIBUTES LIKE '%V%'))
define(is_resident,(NOT MISC_ATTRIBUTES LIKE '%M%'))
RULE 'DATA_POOL_PLACEMENT_RULE' SET POOL 'data'
RULE EXTERNAL POOL 'LTFSEE_FILES'
EXEC '/opt/ibm/ltfsee/bin/ltfsee'
OPTS '-p TIERED1 TIERED2'
RULE 'LTFSEE_FILES_RULE' MIGRATE FROM POOL 'data'
THRESHOLD(90,80)
TO POOL 'LTFSEE_FILES'
WHERE FILE_SIZE > 1048576
AND (CURRENT_TIMESTAMP - ACCESS_TIME > INTERVAL '525600' MINUTES )
AND (CURRENT_TIMESTAMP - MODIFICATION_TIME > INTERVAL '525600' MINUTES )
AND is_resident OR is_premigrated
AND NOT user_exclude_list
AND user_include_list
Troubleshooting
Logging
LTFS logs are located at /var/log/ltfsee.log.
Additional logs worth investigating:
/opt/tivoli/tsm/client/hsm/bin/dsmerror.log
The reclamation process failed
Two tape drives have tapes in it but doesn't appear to be doing anything. Looking at /var/log/ltfsee.log, we can see that the reclamation process failed. The T00037L8 tape was in a drive that stopped functioning, showing a '5' in the single character display with the cartridge ejected.
Addendum: Bad Tape?
After a week, the same error occurred again with the same tape cartridge. It's most likely that theT00037L8 tape cartridge is faulty.
2020-01-20T10:23:05.514522-07:00 ltfs reclaim_target[10652]: GLESA112E(00590): The following command failed with (rc:256:1) : /bin/cp /ltfs/T00037L8/.LTFSEE_DATA/10991691794470275686-15679318773138264748-78339434-18551699-0 /ltfs/T00022L8/.LTFSEE_DATA 2>&1.
2020-01-20T10:23:14.925509-07:00 ltfs reclaim_target[10652]: GLESA112E(00590): The following command failed with (rc:256:1) : /bin/cp /ltfs/T00037L8/.LTFSEE_DATA/10991691794470275686-15679318773138264748-78339434-18551699-0 /ltfs/T00022L8/.LTFSEE_DATA 2>&1.
2020-01-20T10:23:14.925818-07:00 ltfs reclaim_target[10652]: GLESR035E(01182): The copy process from source to destination tape failed for the file 10991691794470275686-15679318773138264748-78339434-18551699-0.
2020-01-20T10:23:14.926141-07:00 ltfs reclaim_target[10652]: GLESR004E(01930): Processing file /tiered/ewang/xuexu/dbgap_tcga_germline/SRR3341182_SRR3341183_varscan.pileup failed: exiting the reclamation driver.
2020-01-20T10:23:14.926413-07:00 ltfs reclaim_target[10652]: GLESR026E(00158): The reclamation process failed (1932).#012 Have a look for previous messages.
2020-01-20T10:23:14.927489-07:00 ltfs mmm[2692]: GLESM221E(02136): Generic job with identifier REC_TGTT00022L8 failed.
2020-01-20T10:23:15.501824-07:00 ltfs mmm[2692]: GLESM223E(02024): Not all generic requests for session 1447695617 have been successful: 1 failed.
2020-01-20T10:23:15.502533-07:00 ltfs mmm[2692]: GLESM221E(02136): Generic job with identifier REC_SRCT00037L8 failed.
2020-01-20T10:23:16.130885-07:00 ltfs mmm[2692]: GLESM223E(02024): Not all generic requests for session 1442649089 have been successful: 1 failed.
2020-01-20T10:23:16.132052-07:00 ltfs ltfsee[14335]: GLESL082E(01590): Reclamation failed while reclaiming tape T00037L8 to target tape T00022L8.
2020-01-26T05:00:02.516999-07:00 ltfs ltfsee[23826]: GLESL668E(00979): Unable to get the state of tape T00030L8. Skip to reclaim. Consult the log files. (rc=1040)
2020-01-26T05:00:02.823888-07:00 ltfs ltfsee[23826]: GLESL682E(01028): Tape with ID: T00030L8 is an invalid state. Source tapes must be in state either "Valid LTFS" or "Warning".
2020-01-26T05:04:36.512781-07:00 ltfs reclaim_target[31377]: GLESR030E(00178): The reclamation process failed. (1655)#012 Have a look for previous messages.
2020-01-26T05:04:36.513142-07:00 ltfs mmm[2692]: GLESM221E(02136): Generic job with identifier REC_TGTT00029L8 failed.
2020-01-26T05:04:36.620168-07:00 ltfs mmm[2692]: GLESM223E(02024): Not all generic requests for session 2135234305 have been successful: 1 failed.
The two drives that are still in use are idling for the past week. Interestingly, ltfsee log did not show any information for 31L8 and 54L8 tapes.
[root@ltfs ~]# ltfsee info jobs
Job Type Status Idle(sec) Scan ID Tape Pool Library Node File Name or inode
Reclaim(Source) In-progress 576566 2944737025 T00031L8 TIERED1 T_ARCH 4 -
Reclaim(Target) In-progress 576438 2944737281 T00054L8 TIERED1 T_ARCH 4 -
Validate Unscheduled 7224 1602429441 T00054L8 TIERED1 T_ARCH - -
The job cannot be stopped. Force a LTFS stop using ltfsee stop -f and wait. The tapes drives should eventually eject the tapes. I got the following error when stopping, but the tapes got ejected and everything seemed to have stopped.
[root@ltfs ~]# ltfsee stop -f
Library name: T_ARCH, library serial: 0000078BA6130402, control node (ltfsee_md) IP address: 172.26.3.249.
Running stop command - sending request and waiting for the completion.
GLESL030E(00909): Unable to connect to the MMM service. Check whether the IBM Spectrum Archive EE has been started.
GLESL358E(00494): Error on processing tape T00054L8 (1).
GLESL661E(00104): IPC got failure result (result=1).
GLESL646E(00164): Unable to stop the IBM Spectrum Archive EE monitor daemon for library T_ARCH.
Cannot Start LTFS
[root@ltfs ~]# /opt/ibm/ltfsee/bin/ltfsee start
Library name: T_ARCH, library serial: 0000078BA6130402, control node (ltfsee_md) IP address: 172.26.3.249.
Running start command - sending request : T_ARCH.
Running start command - waiting for completion : T_ARCH.
...
GLESL657E(00191): Fail to start the IBM Spectrum Archive EE service (MMM) for library T_ARCH.
Use the 'ltfsee info nodes' command to see the error modules.
The monitor daemon will start the recovery sequence.
[root@ltfs ~]# ltfsee info nodes
Spectrum Archive EE service (MMM) for library T_ARCH fails to start or is not running on ltfs-ib.gpfs.net Node ID:4
Problem Detected:
Node ID Error Modules
4 MMM;
Looking at /var/log/ltfsee.log, we see:
2020-02-03T13:15:35.266926-07:00 ltfs mmm[31142]: GLESM709E(00369): Assign tape (T00099L8) command error: 172.26.3.249:7600 (4): Request Error (070E): [Cartridge.cc:61]: Cartridge add is failed: 7c05 LTFSI1079E The operation is not allowed.
Seemed to have started up by itself?
[root@ltfs ~]# /opt/ibm/ltfsee/bin/ltfsee start
Library name: T_ARCH, library serial: 0000078BA6130402, control node (ltfsee_md) IP address: 172.26.3.249.
GLESL519I(00344): The IBM Spectrum Archive EE service (ltfsee_md) for library T_ARCH is already running.
[root@ltfs ~]# ltfsee info nodes
Node ID Status Node IP Drives Ctrl Node Library Node Group Host Name
4 Available 172.26.3.249 3 yes(active) T_ARCH G0 ltfs-ib.gpfs.net
Not sure what happened there...
Invalid Tapes
[root@ltfs ~]# ltfsee info tapes
Tape ID Status Type Capacity(GiB) Used(GiB) Free(GiB) Reclaimable(GiB) Pool Library Address Drive Appendable
T00030L8 Invalid L8 10907 10895 0 22 TIERED1 T_ARCH 1131 - no
T00099L8 Invalid L8 10907 10883 0 0 TIERED2 T_ARCH 1031 - no
According to IBM's documentation:
The Invalid status indicates that the cartridge is inconsistent with the LTFS format.To check and repair this tape before you add it to a tape storage pool, use the ltfsee pool add command with the check option.
In order to add the tape back into the pool, it has to be removed first.
[root@ltfs ~]# ltfsee pool add -p TIERED2 -t T00099L8 -c
GLESL042I(00894): Adding tape T00099L8 to storage pool TIERED2.
GLESL346E(00949): No tapes are found in the unassigned list. T00099L8 is already assigned to another storage pool, is in an IE slot, or does not exist in the library.
[root@ltfs ~]# ltfsee pool remove -p TIERED2 -t T00099L8
GLESL043I(01134): Removing tape T00099L8 from storage pool TIERED2.
Removed tape T00099L8 from pool TIERED2 successfully.
[root@ltfs ~]# ltfsee pool add -p TIERED2 -t T00099L8 -c
GLESL042I(00894): Adding tape T00099L8 to storage pool TIERED2.
Tape T00099L8 successfully checked.
Added tape T00099L8 to pool TIERED2 successfully.
The checking step takes a very long time, upwards to an hour for this LTO8 cartridge. The tape drive status will be shown as 'locating' and ltfsee info jobs show the recovery job idling. This however appears to be normal since it eventually finished.
[root@ltfs ~]# ltfsee info jobs
Job Type Status Idle(sec) Scan ID Tape Pool Library Node File Name or inode
Recovery Scheduled 694 2181628673 T00099L8 TIERED2 T_ARCH 4 -
Error Tape Drives
One of the tape drives is in 'Error' state.
[root@ltfs ~]# ltfsee info drives
Drive S/N Status Type Role Library Address Node ID Tape Node Group
0007807A4B In use LTO8 mrg T_ARCH 260 4 T00000L8 G0
0007807A0B Error LTO8 mrg T_ARCH 261 4 - G0
000780765B In use LTO8 mrg T_ARCH 262 4 T00037L8 G0
The drive shows up as online to the tape library. No visible errors displayed on the tape drive itself.
I can't remove/readd it:
[root@ltfs ~]# ltfsee drive remove -d 0007807A0B
GLESL132E(00247): Could not remove a drive 0007807A0B. Drive is not in mount or not mounted state. The tape drive status:2.
Stopping and starting LTFSEE seemed to have cleared this error.
[root@ltfs ~]# ltfsee stop
Library name: T_ARCH, library serial: 0000078BA6130402, control node (ltfsee_md) IP address: 172.26.3.249.
Running stop command - sending request and waiting for the completion.
...
Stopped the IBM Spectrum Archive EE services for library T_ARCH.
[root@ltfs ~]# ltfsee start
Library name: T_ARCH, library serial: 0000078BA6130402, control node (ltfsee_md) IP address: 172.26.3.249.
Running start command - sending request : T_ARCH.
Running start command - waiting for completion : T_ARCH.
.....................................
Started the IBM Spectrum Archive EE services for library T_ARCH with good status.
[root@ltfs ~]# ltfsee info drives
Drive S/N Status Type Role Library Address Node ID Tape Node Group
0007807A4B Not mounted LTO8 mrg T_ARCH 260 4 - G0
0007807A0B Not mounted LTO8 mrg T_ARCH 261 4 - G0
000780765B Not mounted LTO8 mrg T_ARCH 262 4 - G0
Interestingly, all tapes that were in drives were stowed away. I believe this is the behavior when shutting down LTFS.
Bad Tape Drive
The TS4500 tape library reported a tape drive issue with the error "Drive internal power-on self-tests failed." code 001F. The LTFS operations that were running at the time on this tape drive stopped and the tape cartridge itself is marked as 'Critical'.
/var/log/ltfsee.log showed:
2020-03-24T19:43:39.873263-06:00 ltfs ltfseecp[21628]: GLESG081E(00468): Migrating data of GPFS file /tiered/kkurek/sbarclay/speedseq_align/73.L005.realign.bam: write failed to tape T00086L8 and file /ltfs/T00086L8/.LTFSEE_DATA/10991691794470275686-15679318773138264748-228651564-67167434-0 (data length: 524288, rc: -1, errno: 5).
2020-03-24T19:43:39.873579-06:00 ltfs ltfseecp[21628]: GLESG506E(00803): Migration file (/tiered/kkurek/sbarclay/speedseq_align/73.L005.realign.bam) to tape T00086L8 failed (1091).
2020-03-24T19:43:39.873870-06:00 ltfs ltfseecp[21628]: GLESC003E(01158): Redundant copy for file /tiered/kkurek/sbarclay/speedseq_align/73.L005.realign.bam to tape T00086L8 failed.
2020-03-24T19:43:39.979980-06:00 ltfs mmm[28988]: GLESM110W(00210): Tape T00086L8 got critical.
2020-03-24T19:44:09.243830-06:00 ltfs mmm[28988]: GLESM709E(00442): Unmount T00086L8 command error: 172.26.3.249:7600 (4): Request Error (077E): [Cartridge.cc:146]: Cartridge unmount is failed: 578a LTFSI1086E This operation is not allowed on a cartridge with a critical error.
2020-03-24T19:44:09.244112-06:00 ltfs mmm[28988]: GLESM118E(00060): Unmount of tape T00086L8 failed (drive 000780765B). Check the state of tapes and drives.
2020-03-24T19:44:39.166261-06:00 ltfs mmm[28988]: GLESM709E(00442): Unmount T00086L8 command error: 172.26.3.249:7600 (4): Request Error (077E): [Cartridge.cc:146]: Cartridge unmount is failed: 5b10 LTFSI1086E This operation is not allowed on a cartridge with a critical error.
2020-03-24T19:44:39.166568-06:00 ltfs mmm[28988]: GLESM118E(00060): Unmount of tape T00086L8 failed (drive 000780765B). Check the state of tapes and drives.
2020-03-24T19:45:09.283571-06:00 ltfs mmm[28988]: GLESM709E(00442): Unmount T00086L8 command error: 172.26.3.249:7600 (4): Request Error (077E): [Cartridge.cc:146]: Cartridge unmount is failed: 5d71 LTFSI1086E This operation is not allowed on a cartridge with a critical error.
2020-03-24T19:45:09.283890-06:00 ltfs mmm[28988]: GLESM118E(00060): Unmount of tape T00086L8 failed (drive 000780765B). Check the state of tapes and drives.
...
2020-03-25T01:19:14.689053-06:00 ltfs ltfsee[14508]: GLESL062E(00577): Tape with ID: T00086L8 is in an invalid state. Tapes must be either in state "Valid LTFS" or "Unknown".
2020-03-25T01:19:14.695195-06:00 ltfs ltfsee[14501]: GLESL062E(00577): Tape with ID: T00086L8 is in an invalid state. Tapes must be either in state "Valid LTFS" or "Unknown".
2020-03-25T01:19:14.700692-06:00 ltfs ltfsee[14503]: GLESL062E(00577): Tape with ID: T00086L8 is in an invalid state. Tapes must be either in state "Valid LTFS" or "Unknown".
2020-03-25T01:19:14.706384-06:00 ltfs ltfsee[14504]: GLESL062E(00577): Tape with ID: T00086L8 is in an invalid state. Tapes must be either in state "Valid LTFS" or "Unknown".
[root@ltfs ~]# ltfsee info tapes
Tape ID Status Type Capacity(GiB) Used(GiB) Free(GiB) Reclaimable(GiB) Pool Library Address Drive Appendable
T00086L8 Critical L8 10907 0 0 0 TIERED2 T_ARCH 262 000780765B no
...
T00084L8 Critical L8 10907 10859 0 0 TIERED2 T_ARCH 262 000780765B no (this happened the next day)
The recovery process from IBM's documentation can be read at https://www.ibm.com/support/knowledgecenter/en/ST9MBR_1.2.4/ltfs_ee_recovering_critical_tapes.html
In summary, the recovery process is to:
- Recover the files from tape back to Spectrum Scale.
## Show all files to recover # ltfsee recover -s -p TIERED2 -l T_ARCH -t T00084L8 ## Recover these files # ltfsee recover -c -p TIERED2 -l T_ARCH -t T00084L8
- Remove the tape from the LTFS library.
## ltfsee recover -r -p TIERED2 -l T_ARCH -t T00084L8
- Move the tape to the IO port.
# ltfsee tape move homeslot -t T00084L8 -p TIERED2
You must recover all files from the tape prior to moving it, or else you will get this error:
# ltfsee tape move homeslot -t T00084L8 -p TIERED2
GLESL373I(00890): Moving tape T00084L8.
GLESL630E(00463): Cannot move tape T00084L8 because the status is "Critical".
Tasks
Shutdown and Startup
If the tape library needs to go offline, turn off LTFS to ensure drives are not accessed.
# ltfsee stop
When completed, start up LTFS:
# ltfsee start
Remove or Reclaim Tape
If a tape needs to be removed from the pool or tape library, you need to first reclaim its data so that migrated or saved files on the tape are retained.
To start a reclaimation for a specific tape, use ltfsee reclaim -p pool -t tapeid:
[root@ltfs ~]# ltfsee reclaim -p TIERED1 -t T00037L8
Start reclaiming 1 tapes in the following list of tapes:
T00037L8 .
Files in tape T00037L8 are copied to tape T00000L8.
Once completed, you should be able to remove the tape from the pool and then move it to the IO slot.
If you don't reclaim the contents first, you will get these error messages:
[root@ltfs ~]# ltfsee pool remove -p TIERED1 -t T00037L8
GLESL043I(01134): Removing tape T00037L8 from storage pool TIERED1.
GLESL357E(01223): Tape T00037L8 has migrated files or saved files. It has not been removed from the pool.
[root@ltfs ~]# ltfsee tape move ieslot -t T00037L8 -p TIERED1
GLESL170E(00472): Failed to move tape T00037L8 because tape is assigned to a pool and not offline.
Cronjobs
The following cronjob is installed.
# Cron Job Used to Move Data Via policy to LTFS Tape at 1:00 AM
00 1 * * * /mmpolicies/movetogpfs1.sh
# Cron Job Used to Move Data Via policy to LTFS Tape at 3:00 AM
00 3 * * * /mmpolicies/movetogpfs0.sh
# Cron Job Used to Reconcile disk data with LTFS Tape data Pool TIERED1
00 20 * * * /opt/ibm/ltfsee/bin/ltfsee reconcile -p TIERED1 -l T_ARCH -g /tiered
# Cron Job Used to Reconcile disk data with LTFS Tape data Pool TIERED2
00 22 * * * /opt/ibm/ltfsee/bin/ltfsee reconcile -p TIERED2 -l T_ARCH -g /tiered
# Cron Job Used to Reclaim LTFS Tape data in Pool TIERED1
00 5 * * sun /opt/ibm/ltfsee/bin/ltfsee reclaim -p TIERED1 -l T_ARCH
# Cron Job Used to Reclaim LTFS Tape Data in Pool TIERED2
00 7 * * sun /opt/ibm/ltfsee/bin/ltfsee reclaim -p TIERED2 -l T_ARCH