ATtiny85: Difference between revisions

From Leo's Notes
This page was last edited on 31 July 2021, at 21:16.
← Older editNewer edit →
VisualWikitext
No edit summary
No edit summary
Line 1: Line 1:
The ATtiny85 is an Atmel 8-bit AVR microcontroller. The ATtiny falls under the tinyAVR series of AVR controllers and is more limited in terms of available memory, IO pins, and peripheral sets when compared to the megaAVR series microcontrollers found in many Arduinos. However, the ATtiny trades these limitations for lower power consumption and smaller form factor.
The ATtiny85 is an Atmel 8-bit AVR microcontroller. The ATtiny falls under the tinyAVR series of AVR controllers and is more limited in terms of available memory, IO pins, and peripheral sets when compared to the megaAVR series microcontrollers found in many Arduinos. However, the ATtiny trades these limitations for lower power consumption and smaller form factor.


=== A quick overview on using the ATtiny ===
== Getting started ==
 
===Connecting the ATtiny for ISP===
[[File:ATtiny25 ATtiny45 ATtiny85 pinout.svg|alt=ATtiny25/ATtiny45/ATtiny85 pinout|thumb|ATtiny25/ATtiny45/ATtiny85 pinout]]
[[File:ATtiny25 ATtiny45 ATtiny85 pinout.svg|alt=ATtiny25/ATtiny45/ATtiny85 pinout|thumb|ATtiny25/ATtiny45/ATtiny85 pinout]]
The ATtiny85 in the DIP/SOIC/SOP package has 8 pins. The pinouts are shown on the right. To program the ATtiny, we will be using ISP via pins 5, 6, and 7 (outlined in orange in the diagram). Any ISP programmer will do, but we will be using an Arudino.
In-system programming (ISP) is used for programming the ATtiny. This is also sometimes referred to as ICSP (In-circuit serial programming).


An Arduino can be converted into an ISP programmer by loading the ArduinoISP sketch from the examples menu. Once the sketch is on the Arduino, connect the ATtiny to the Arduino based on the table below.
The ATtiny85 in the DIP/SOIC/SOP package has 8 pins. The pinouts are shown on the right. To program the ATtiny, we will be using ISP via pins 5, 6, and 7 (outlined in orange in the diagram). Any ISP programmer will do, but we will be using an Arudino running the ArduinoISP sketch which can be found from the examples menu.
 
Once the ArduinoISP sketch is programmed on the Arduino, connect the ATtiny to the Arduino based on the table below.
{| class="wikitable"
{| class="wikitable"
!Arduino Pin
!Arduino Pin
Line 28: Line 32:
|}
|}
Connect ground and power to the ATtiny via the Arudino. You may use either 5 or 3.3 volts. A 10uF capacitor should also be connected between ground and the Arudino reset pin to prevent the Arduino from resetting during the ISP programming. At the end, it should look something like the following:
Connect ground and power to the ATtiny via the Arudino. You may use either 5 or 3.3 volts. A 10uF capacitor should also be connected between ground and the Arudino reset pin to prevent the Arduino from resetting during the ISP programming. At the end, it should look something like the following:
[[File:ATtiny85 ISP connection.svg|alt=ATtiny85 ISP connection|center|thumb|ATtiny85 ISP connection]]
=== Programming the ATtiny with AVRDUDE ===
AVRDude ('''AVR D'''ownloader/'''U'''ploa'''DE'''r) is a utility that can program AVR microcontrollers using ISP. Once the appropriate connections are made, we can use avrdude to read/write to the microcontroller.
avrdude takes some required options:
* <code>-c programmer-id</code> - specify the programmer you are using. When using the Arduino as the ISP programmer, you may use the <code>avrisp</code> or <code>arduino</code> (which appears to be aliases for <code>stk500</code>) as the programmer.
* <code>-p part-number</code>- the board you are targeting
* <code>-P port</code> - the device or port that is connected to the ISP programmer. On Windows, it is probably some <code>COM#</code> port. On Linux, it's likely to be <code>/dev/ttyUSB#</code>.
* <code>-B bit-clock</code> - Used to adjust the SPI speed. Default is 10, for 100KHz. KHz = 1000/(1.5+B).
Some useful commands to be aware of:
{| class="wikitable"
!Task
!Command
|-
|Read fuse settings
|<code>avrdude -c avrisp -b 19200 -p attiny85 -P /dev/ttyUSB0 -U lfuse:r:-:i</code>
|-
|Change fuse settings
|<code>avrdude -c avrisp -b 19200 -p attiny85 -P /dev/ttyUSB0 -U lfuse:w:0xXX:m -U hfuse:w:0xXX:m -U efuse:w:0xXX:m</code>


Be careful when setting the fuses for an external clock. You may need to adjust the SPI speed in your programmer or via the -B option in avrdude.
|-
|Write flash
|<code>avrdude -c avrisp -b 19200 -p attiny85 -P /dev/ttyUSB0 -U flash:w:firmware.hex</code>
|}


== Other notes ==
=== ATtiny configuration fuses ===
There are some configuration settings that can be set on the ATtiny. These settings can change the behavior of the microcontroller such as changing its clock speed or using an external clock source.
Despite its name, these fuses are really just flash/EEPROM values used as configuration parameters. You may change these values at a later time and are values don't actually blow any fuses.
There is a fuse calculator at <nowiki>https://www.engbedded.com/fusecalc/</nowiki> for a wide array of AVR microcontrollers.
<br />
== Implementing the crazy clock with an ATtiny85 ==
<br />
*


Random notes:
Random notes:
Line 42: Line 87:
Fuses
Fuses


*Settings are set with fuses. These fuses are actually flash/eeprom and used as configuration parameters.
*
*Fuse calculator at <nowiki>https://www.engbedded.com/fusecalc/</nowiki>




Revision as of 21:16, 31 July 2021

The ATtiny85 is an Atmel 8-bit AVR microcontroller. The ATtiny falls under the tinyAVR series of AVR controllers and is more limited in terms of available memory, IO pins, and peripheral sets when compared to the megaAVR series microcontrollers found in many Arduinos. However, the ATtiny trades these limitations for lower power consumption and smaller form factor.

Getting started

Connecting the ATtiny for ISP

ATtiny25/ATtiny45/ATtiny85 pinout
ATtiny25/ATtiny45/ATtiny85 pinout

In-system programming (ISP) is used for programming the ATtiny. This is also sometimes referred to as ICSP (In-circuit serial programming).

The ATtiny85 in the DIP/SOIC/SOP package has 8 pins. The pinouts are shown on the right. To program the ATtiny, we will be using ISP via pins 5, 6, and 7 (outlined in orange in the diagram). Any ISP programmer will do, but we will be using an Arudino running the ArduinoISP sketch which can be found from the examples menu.

Once the ArduinoISP sketch is programmed on the Arduino, connect the ATtiny to the Arduino based on the table below.

Arduino Pin Function Connect to ATtiny85 Pin
10 Reset 1
11 MOSI 5
12 MISO 6
13 SCK 7

Connect ground and power to the ATtiny via the Arudino. You may use either 5 or 3.3 volts. A 10uF capacitor should also be connected between ground and the Arudino reset pin to prevent the Arduino from resetting during the ISP programming. At the end, it should look something like the following:

ATtiny85 ISP connection
ATtiny85 ISP connection

Programming the ATtiny with AVRDUDE

AVRDude (AVR Downloader/UploaDEr) is a utility that can program AVR microcontrollers using ISP. Once the appropriate connections are made, we can use avrdude to read/write to the microcontroller.

avrdude takes some required options:

  • -c programmer-id - specify the programmer you are using. When using the Arduino as the ISP programmer, you may use the avrisp or arduino (which appears to be aliases for stk500) as the programmer.
  • -p part-number- the board you are targeting
  • -P port - the device or port that is connected to the ISP programmer. On Windows, it is probably some COM# port. On Linux, it's likely to be /dev/ttyUSB#.
  • -B bit-clock - Used to adjust the SPI speed. Default is 10, for 100KHz. KHz = 1000/(1.5+B).

Some useful commands to be aware of:

Task Command
Read fuse settings avrdude -c avrisp -b 19200 -p attiny85 -P /dev/ttyUSB0 -U lfuse:r:-:i
Change fuse settings avrdude -c avrisp -b 19200 -p attiny85 -P /dev/ttyUSB0 -U lfuse:w:0xXX:m -U hfuse:w:0xXX:m -U efuse:w:0xXX:m

Be careful when setting the fuses for an external clock. You may need to adjust the SPI speed in your programmer or via the -B option in avrdude.

Write flash avrdude -c avrisp -b 19200 -p attiny85 -P /dev/ttyUSB0 -U flash:w:firmware.hex

Other notes

ATtiny configuration fuses

There are some configuration settings that can be set on the ATtiny. These settings can change the behavior of the microcontroller such as changing its clock speed or using an external clock source.

Despite its name, these fuses are really just flash/EEPROM values used as configuration parameters. You may change these values at a later time and are values don't actually blow any fuses.

There is a fuse calculator at https://www.engbedded.com/fusecalc/ for a wide array of AVR microcontrollers.

Implementing the crazy clock with an ATtiny85


Random notes:

  • All 6 port B pins can be used as IO lines to the internal 8 bit bus (high bits, lower 2 bits aren't connected?)
  • System clock can be selected with CKSEL. It can use the internal 8MHz ocillator (with some options which sets it to 16 or 8mhz) An external clock is given with XTAL1 and XTAL2.
  • Regardless of the oscillator, CLKPS sets the prescaler
  • Setting the wrong clock setting can be problematic to recover from. You would likely need to inject a clock signal.


Fuses


Other resources


Comparisons

The distinction between the other ATtiny microprocessors are:

ATTiny25 ATTiny45 ATTiny85
Programmable Flash Memory (10k write/erase) 2K 4K 8K
EEPROM (100k write/erase) 128 bytes 256 bytes 512 bytes
SRAM 128 bytes 256 bytes 512 bytes
Program Counter bits wide 10 11 12