WZR-600DHP - Revision history

Leo: /* Is the WAN port actually gigabit? */

2023-12-03T07:48:36Z

Is the WAN port actually gigabit?

← Older revision		Revision as of 07:48, 3 December 2023
Line 208:		Line 208:
	VCED exceptions : not available		VCED exceptions : not available
	VCEI exceptions : not available		VCEI exceptions : not available

			root@OpenWrt:~# cat /etc/os-release
			NAME="OpenWrt"
			VERSION="21.02.0"
			ID="openwrt"
			ID_LIKE="lede openwrt"
			PRETTY_NAME="OpenWrt 21.02.0"
			VERSION_ID="21.02.0"
			HOME_URL="https://openwrt.org/"
			BUG_URL="https://bugs.openwrt.org/"
			SUPPORT_URL="https://forum.openwrt.org/"
			BUILD_ID="r16279-5cc0535800"
			OPENWRT_BOARD="ath79/generic"
			OPENWRT_ARCH="mips_24kc"
			OPENWRT_TAINTS=""
			OPENWRT_DEVICE_MANUFACTURER="OpenWrt"
			OPENWRT_DEVICE_MANUFACTURER_URL="https://openwrt.org/"
			OPENWRT_DEVICE_PRODUCT="Generic"
			OPENWRT_DEVICE_REVISION="v0"
			OPENWRT_RELEASE="OpenWrt 21.02.0 r16279-5cc0535800"
	\| lang = terminal		\| lang = terminal
	}}		}}
	All the spec sheets for the device says it is a gigabit capable device on all LAN and WAN ports. 🤔		All the spec sheets for the device says it is a gigabit capable device on all LAN and WAN ports. 🤔

	I then did a sysupgrade to the latest OpenWRT release (23.05.0) and.... lo and ~~be hold~~:		I then did a sysupgrade from OpenWRT 21.02.0 to the latest OpenWRT release (23.05.0) and.... lo and behold the interface came up with gigabit:
	{{Highlight		{{Highlight
	\| code = root@OpenWrt:~# ethtool -I eth1		\| code = root@OpenWrt:~# ethtool -I eth1
Line 247:		Line 267:
	\| lang = terminal		\| lang = terminal
	}}		}}
	~~The upgrade brought in the full link speed.~~ OpenWRT's great 🎉		OpenWRT's great 🎉

	== See also ==		== See also ==

	* https://openwrt.org/toh/buffalo/wzr-hp-ag300h		* https://openwrt.org/toh/buffalo/wzr-hp-ag300h

Leo: /* Setup a print server using p910nd */

2023-12-03T07:45:52Z

Setup a print server using p910nd

← Older revision		Revision as of 07:45, 3 December 2023
Line 65:		Line 65:

	=== Setup a print server using p910nd ===		=== Setup a print server using p910nd ===
			[[File:OpenWRT p910nd configuration.png\|thumb\|OpenWRT p910nd configuration]]
	On the stock dd-wrt firmware, you can enable USB printer support which starts a p910nd service that exposes the USB printer on port 9100.		On the stock dd-wrt firmware, you can enable USB printer support which starts a p910nd service that exposes the USB printer on port 9100.

Leo at 07:35, 3 December 2023

2023-12-03T07:35:43Z

← Older revision		Revision as of 07:35, 3 December 2023
Line 218:		Line 218:
	Supported link modes: 10baseT/Half 10baseT/Full		Supported link modes: 10baseT/Half 10baseT/Full
	100baseT/Half 100baseT/Full		100baseT/Half 100baseT/Full
			1000baseT/Full
	Supported pause frame use: Symmetric Receive-only		Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes		Supports auto-negotiation: Yes
Line 223:		Line 224:
	Advertised link modes: 10baseT/Half 10baseT/Full		Advertised link modes: 10baseT/Half 10baseT/Full
	100baseT/Half 100baseT/Full		100baseT/Half 100baseT/Full
	Advertised pause frame use: No		1000baseT/Full
			Advertised pause frame use: Symmetric Receive-only
	Advertised auto-negotiation: Yes		Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported		Advertised FEC modes: Not reported
	Link partner advertised link modes: 10baseT/Half 10baseT/Full		Link partner advertised link modes: 10baseT/Half 10baseT/Full
	100baseT/Half 100baseT/Full		100baseT/Half 100baseT/Full
			1000baseT/Half 1000baseT/Full
	Link partner advertised pause frame use: No		Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes		Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported		Link partner advertised FEC modes: Not reported
	Speed: ~~100Mb~~/s		Speed: 1000Mb/s
	Duplex: Full		Duplex: Full
	Port: ~~MII~~		Port: Twisted Pair
	PHYAD: 4		PHYAD: 4
	Transceiver: external		Transceiver: external
	Auto-negotiation: on		Auto-negotiation: on
			MDI-X: Unknown
	Current message level: 0x000000ff (255)		Current message level: 0x000000ff (255)
	drv probe link timer ifdown ifup rx_err tx_err		drv probe link timer ifdown ifup rx_err tx_err

Leo: Undo revision 7410 by Leo (talk)

2023-12-03T07:35:15Z

Undo revision 7410 by Leo (talk)

← Older revision		Revision as of 07:35, 3 December 2023
Line 211:		Line 211:
	All the spec sheets for the device says it is a gigabit capable device on all LAN and WAN ports. 🤔		All the spec sheets for the device says it is a gigabit capable device on all LAN and WAN ports. 🤔

	I then did a sysupgrade to the latest OpenWRT release (23.05.0) and ~~it made no difference~~:		I then did a sysupgrade to the latest OpenWRT release (23.05.0) and.... lo and be hold:
	{{Highlight		{{Highlight
	\| code = root@OpenWrt:~# ethtool -I eth1		\| code = root@OpenWrt:~# ethtool -I eth1
Line 242:		Line 242:
	\| lang = terminal		\| lang = terminal
	}}		}}
			The upgrade brought in the full link speed. OpenWRT's great 🎉

	== See also ==		== See also ==

	* https://openwrt.org/toh/buffalo/wzr-hp-ag300h		* https://openwrt.org/toh/buffalo/wzr-hp-ag300h

Leo: /* Is the WAN port actually gigabit? */

2023-12-03T07:34:32Z

Is the WAN port actually gigabit?

← Older revision		Revision as of 07:34, 3 December 2023
Line 211:		Line 211:
	All the spec sheets for the device says it is a gigabit capable device on all LAN and WAN ports. 🤔		All the spec sheets for the device says it is a gigabit capable device on all LAN and WAN ports. 🤔

	I then did a sysupgrade to the latest OpenWRT release (23.05.0) and~~.... lo and be hold~~:		I then did a sysupgrade to the latest OpenWRT release (23.05.0) and it made no difference:
	{{Highlight		{{Highlight
	\| code = root@OpenWrt:~# ethtool -I eth1		\| code = root@OpenWrt:~# ethtool -I eth1
Line 242:		Line 242:
	\| lang = terminal		\| lang = terminal
	}}		}}
	~~The upgrade brought in the full link speed. OpenWRT's great 🎉~~

	== See also ==		== See also ==

	* https://openwrt.org/toh/buffalo/wzr-hp-ag300h		* https://openwrt.org/toh/buffalo/wzr-hp-ag300h

Leo: gigabit on wan

2023-12-03T07:33:52Z

gigabit on wan

@@ Line 129: / Line 129: @@
 <6>[  555.500000] usbcore: registered new interface driver usblp
 }}
 == See also ==
 * https://openwrt.org/toh/buffalo/wzr-hp-ag300h

Leo at 06:46, 2 June 2022

2022-06-02T06:46:49Z

← Older revision		Revision as of 06:46, 2 June 2022
Line 1:		Line 1:
	The Buffalo WZR-600DHP is a 802.11n router. This router is based on the Atheros AR7161 SoC with 128MB memory and 32MB flash.		The Buffalo WZR-600DHP is a 802.11n router. This router is based on the Atheros AR7161 SoC with 128MB memory and 32MB flash.

	The last firmware that Buffalo provided for this unit is DD-WRT v3.0-r30356 std (11/30/17). For continued support, ~~you can flash~~ OpenWRT.		The last firmware that Buffalo provided for this unit is DD-WRT v3.0-r30356 std (11/30/17). This version of dd-wrt is based on Linux 3.10.102, built on November 30, 2017. For continued support, use OpenWRT which still continues to build recent revisions for this unit.

	I purchased this unit back in February 2014 from NewEgg for $80.		I purchased this unit back in February 2014 from NewEgg for $80.

Leo at 06:14, 2 June 2022

2022-06-02T06:14:48Z

← Older revision		Revision as of 06:14, 2 June 2022
Line 1:		Line 1:
	The Buffalo WZR-600DHP is a 802.11n router.		The Buffalo WZR-600DHP is a 802.11n router. This router is based on the Atheros AR7161 SoC with 128MB memory and 32MB flash.

	The last firmware that Buffalo provided for this unit is DD-WRT v3.0-r30356 std (11/30/17). For continued support, ~~load~~ OpenWRT.		The last firmware that Buffalo provided for this unit is DD-WRT v3.0-r30356 std (11/30/17). For continued support, you can flash OpenWRT.

			I purchased this unit back in February 2014 from NewEgg for $80.

	== Flashing OpenWRT on the WZR-600DHP ==		== Flashing OpenWRT on the WZR-600DHP ==
Line 127:		Line 129:
	<6>[ 555.500000] usbcore: registered new interface driver usblp		<6>[ 555.500000] usbcore: registered new interface driver usblp
	}}		}}

			== See also ==

			* https://openwrt.org/toh/buffalo/wzr-hp-ag300h

Leo: p910nd print service

2022-06-02T05:52:42Z

p910nd print service

← Older revision		Revision as of 05:52, 2 June 2022
Line 59:		Line 59:
	arp -d 192.168.11.1		arp -d 192.168.11.1
	}}The router will be accessible at 192.168.11.1 with the new stock firmware. Log in as 'admin' using 'password' as the password.		}}The router will be accessible at 192.168.11.1 with the new stock firmware. Log in as 'admin' using 'password' as the password.

			== Tasks ==

			=== Setup a print server using p910nd ===
			On the stock dd-wrt firmware, you can enable USB printer support which starts a p910nd service that exposes the USB printer on port 9100.

			On OpenWRT, this can also be set up by installing the <code>p910nd</code>, <code>luci-app-p910nd</code>, and <code>kmod-usb-printer</code> packages. Refresh the luci web interface and navigate to Services -> "p910nd - Print Server". Enable the service for <code>/dev/usb/lp0</code> on port 9100.

	== Troubleshooting ==		== Troubleshooting ==

Leo at 05:45, 2 June 2022

2022-06-02T05:45:03Z

← Older revision		Revision as of 05:45, 2 June 2022
Line 21:		Line 21:
	The unit will start a TFTP server for a few seconds as part of the boot sequence. During this short window, it will accept a file via TFTP from 192.168.11.2.		The unit will start a TFTP server for a few seconds as part of the boot sequence. During this short window, it will accept a file via TFTP from 192.168.11.2.

	You will need to prepare a Linux system on the network on this IP address. Use the following commands to set up the IP address and ARP entry (the bootloader fakes this MAC address). Use Curl to push the file via tftp.		You will need to prepare a Linux system on the network on this IP address. Use the following commands to set up the IP address and ARP entry (the bootloader fakes this MAC address). Use Curl to push the file via <code>tftp</code>.
	{{Highlight		{{Highlight
	\| code = # ip address add 192.168.11.2/24 dev ens33		\| code = # ip address add 192.168.11.2/24 dev ens33
Line 28:		Line 28:
	\| lang = terminal		\| lang = terminal
	}}		}}
	~~Powercycle~~ the router and then run the curl command. After a few seconds, you should see curl transmitting the file. Once the curl finishes, it will take the unit a few more to finish flashing. The diagnostic red LED should be blinking until this process is done.		Power cycle the router and then run the <code>curl</code> command. After a few seconds, you should see curl transmitting the file. Once the curl finishes, it will take the unit a few more minutes to finish flashing. The diagnostic red LED should be blinking until this process is done.

			Once you're done, you might want to clear the ARP entry using: <code>arp -d 192.168.11.1</code>

	=== Accessing OpenWRT ===		=== Accessing OpenWRT ===
Line 34:		Line 36:

	==Reverting to the stock firmware==		==Reverting to the stock firmware==
	After being unable to get this router working with a USB printer, I decided to revert from OpenWRT back to the stock dd-wrt based firmware.{{highlight\|lang=terminal\|code=		After being unable to get this router working with a USB printer, I decided to revert from OpenWRT back to the stock dd-wrt based firmware. This can be accomplished using the TFTP bootloader method.{{highlight
			\| lang = terminal
			\| code = # ip address add 192.168.11.2/24 dev ens33
	# arp -s 192.168.11.1 02:aa:bb:cc:dd:20		# arp -s 192.168.11.1 02:aa:bb:cc:dd:20
	## ~~Type~~ the ~~following, but don't run~~ the PUT command ~~just yet.~~
	~~## Power on~~ the device~~. When~~ the router's link light ~~blinks on startup, press the enter key~~.		## Use either curl or tftp
			# curl -T wzr600dhp-pro-v3.0-r30356.enc tftp//192.168.11.1

			## OR use tftp
			## Run every command blow except the PUT command. Run the PUT command only when you have power cycled the device and the router's link light beings blinking.
	# tftp 192.168.11.1		# tftp 192.168.11.1
	tftp> binary		tftp> binary
Line 50:		Line 58:
	## Clear the ARP table:		## Clear the ARP table:
	arp -d 192.168.11.1		arp -d 192.168.11.1
	}}The router will be accessible at 192.168.11.1 with the new stock firmware ~~with the stock username/password~~ 'admin' ~~and~~ 'password.		}}The router will be accessible at 192.168.11.1 with the new stock firmware. Log in as 'admin' using 'password' as the password.

	== Troubleshooting ==		== Troubleshooting ==