Ipmitool - Revision history

Leo at 15:42, 13 September 2024

2024-09-13T15:42:35Z

← Older revision		Revision as of 15:42, 13 September 2024
Line 34:		Line 34:
	\|Clear system event logs / amber light		\|Clear system event logs / amber light
	\|<code>ipmitool sel clear</code>		\|<code>ipmitool sel clear</code>
			\|-
			\|Print sensor information
			\|<code>ipmitool sensor</code>
	\|-		\|-
	\|Powercycle a machine		\|Powercycle a machine

Leo at 22:31, 30 January 2023

2023-01-30T22:31:22Z

← Older revision		Revision as of 22:31, 30 January 2023
Line 140:		Line 140:

	The data can be parsed then pushed into a logging server.		The data can be parsed then pushed into a logging server.

			=== Enable Serial Over Lan (SOL) ===
			You can verify the SOL status via ipmitool by running <code>ipmitool sol info 1</code>. If you use the lanplus interface, <code>ipmitool -I lanplus -U root -H $DRACIP sol info</code>. The output should look something like this:
			{{Highlight
			\| code = # ipmitool sol info 1
			Info: SOL parameter 'Nonvolatile Bitrate (5)' not supported
			Info: SOL parameter 'Volatile Bitrate (6)' not supported
			Set in progress : set-complete
			Enabled : false
			Force Encryption : false
			Force Authentication : false
			Privilege Level : USER
			Character Accumulate Level (ms) : 60
			Character Send Threshold : 96
			Retry Count : 7
			Retry Interval (ms) : 500
			Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
			Non-Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
			Payload Channel : 1 (0x01)
			Payload Port : 623
			\| lang = terminal
			}}
			To enable SOL, set the 'Enabled' property to 'true'. This can only be done using the lanplus interface.
			{{Highlight
			\| code = # ipmitool -I lanplus -U root -H XXX sol set enabled true 1
			Password:

			# ipmitool -I lanplus -U root -H XXX sol info
			Password:
			Info: SOL parameter 'Nonvolatile Bitrate (5)' not supported
			Info: SOL parameter 'Volatile Bitrate (6)' not supported
			Set in progress : set-complete
			Enabled : true
			Force Encryption : false
			Force Authentication : false
			Privilege Level : USER
			Character Accumulate Level (ms) : 60
			Character Send Threshold : 96
			Retry Count : 7
			Retry Interval (ms) : 500
			Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
			Non-Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
			Payload Channel : 1 (0x01)
			Payload Port : 623
			\| lang = terminal
			}}

	==Troubleshooting==		==Troubleshooting==

Leo: /* Usage */

2021-12-18T23:50:45Z

Usage

← Older revision		Revision as of 23:50, 18 December 2021
Line 13:		Line 13:

	==Usage==		==Usage==
			{\| class="wikitable"
	~~=== Change~~ iDRAC network settings ~~===~~		!Task
	{{Highlight		!Command
	\| code = # ~~sudo~~ ipmitool lan set 1 ipsrc static		\|-
	# ~~sudo~~ ipmitool lan set 1 ipaddr 10.1.1.21		\|Print the iDRAC network settings
	# ~~sudo~~ ipmitool lan set 1 netmask 255.255.255.0		\|<code>ipmitool lan print</code>
	# ~~sudo~~ ipmitool lan set 1 defgw ipaddr 10.1.1.1		\|-
			\|Set the iDRAC network settings
			\|{{Highlight
			\| code = # ipmitool lan set 1 ipsrc static
			# ipmitool lan set 1 ipaddr 10.1.1.21
			# ipmitool lan set 1 netmask 255.255.255.0
			# ipmitool lan set 1 defgw ipaddr 10.1.1.1
	\| lang = terminal		\| lang = terminal
	}}		}}
			\|-
	~~===~~ Reset iDRAC account password ~~===~~		\|View system event logs
	{{Highlight		\|<code>ipmitool sel elist</code>
			\|-
			\|Clear system event logs / amber light
			\|<code>ipmitool sel clear</code>
			\|-
			\|Powercycle a machine
			\|<code>ipmitool -U ''username'' -f ''passwd.txt'' -I lanplus -H ''hostname'' chassis power cycle</code>
			\|-
			\|Reset iDRAC account password
			\|{{Highlight
	\| code = # ipmitool user list 1		\| code = # ipmitool user list 1
	ID Name Callin Link Auth IPMI Msg Channel Priv Limit		ID Name Callin Link Auth IPMI Msg Channel Priv Limit
Line 49:		Line 64:
	\| lang = terminal		\| lang = terminal
	}}		}}
			\|}

			== Tasks ==

	===View System Event Logs===		===View System Event Logs===
Line 68:		Line 86:
	\| lang = terminal		\| lang = terminal
	}}		}}

	~~===Clearing System Event Log===~~
	~~Run {{code\|ipmitool sel clear}} to clear all SEL logs. This is useful if your machine has an amber light due to a machine check which you wish to clear.~~

	~~===Power Cycle Machine===~~
	~~To power cycle a machine: <code>ipmitool -U ''username'' -f ''passwd.txt'' -I lanplus -H ''hostname'' chassis power cycle</code>~~

	===Polling Data===		===Polling Data===

Leo at 20:59, 20 April 2021

2021-04-20T20:59:15Z

@@ Line 13: / Line 13: @@
 ==Usage==
 ===View System Event Logs===
@@ Line 36: / Line 72: @@
 Run {{code|ipmitool sel clear}} to clear all SEL logs.  This is useful if your machine has an amber light due to a machine check which you wish to clear.
-=== Power Cycle Machine ===
+===Power Cycle Machine===
 To power cycle a machine: <code>ipmitool -U ''username'' -f ''passwd.txt'' -I lanplus -H ''hostname'' chassis power cycle</code>

Leo: /* Power cycle */

2020-09-24T16:41:42Z

Power cycle

← Older revision		Revision as of 16:41, 24 September 2020
Line 14:		Line 14:
	==Usage==		==Usage==

	=== View System Event Logs ===		===View System Event Logs===
	Use <code>ipmitool sel elist</code> to show logs.		Use <code>ipmitool sel elist</code> to show logs.
	{{Highlight		{{Highlight
Line 35:		Line 35:
	===Clearing System Event Log===		===Clearing System Event Log===
	Run {{code\|ipmitool sel clear}} to clear all SEL logs. This is useful if your machine has an amber light due to a machine check which you wish to clear.		Run {{code\|ipmitool sel clear}} to clear all SEL logs. This is useful if your machine has an amber light due to a machine check which you wish to clear.

			=== Power Cycle Machine ===
			To power cycle a machine: <code>ipmitool -U ''username'' -f ''passwd.txt'' -I lanplus -H ''hostname'' chassis power cycle</code>

	===Polling Data===		===Polling Data===

Leo: view system logs

2020-09-15T18:15:39Z

view system logs

← Older revision		Revision as of 18:15, 15 September 2020
Line 2:		Line 2:

	The project can be found at:		The project can be found at:
	* https://github.com/ipmitool/ipmitool

	== Installation ==		*https://github.com/ipmitool/ipmitool

			==Installation==
	Clone the repository from https://github.com/ipmitool/ipmitool, then run {{code\|autoconf}}, {{code\|./configure}}, {{code\|make}}.		Clone the repository from https://github.com/ipmitool/ipmitool, then run {{code\|autoconf}}, {{code\|./configure}}, {{code\|make}}.

	A docker image containing this binary can be found at:		A docker image containing this binary can be found at:
	* https://git.steamr.com/docker/alpine-ipmitool

	== Usage ==		*https://git.steamr.com/docker/alpine-ipmitool
	=== Clearing System Event Log ===
			==Usage==

			=== View System Event Logs ===
			Use <code>ipmitool sel elist</code> to show logs.
			{{Highlight
			\| code = # ipmitool sel elist
			1 {{!}} 08/24/2006 {{!}} 14:05:17 {{!}} Event Logging Disabled SEL {{!}} Log area reset/cleared {{!}} Asserted
			2 {{!}} 12/11/2008 {{!}} 03:21:50 {{!}} Memory ECC Corr Err {{!}} Correctable ECC (Correctable ECC {{!}} Bank 1DIMM B) {{!}} Asserted
			3 {{!}} Pre-Init {{!}}0000000011{{!}} Physical Security Intrusion {{!}} General Chassis intrusion {{!}} Asserted
			4 {{!}} Pre-Init {{!}}0000000017{{!}} Physical Security Intrusion {{!}} General Chassis intrusion {{!}} Deasserted
			5 {{!}} Pre-Init {{!}}0000000011{{!}} Physical Security Intrusion {{!}} General Chassis intrusion {{!}} Asserted
			6 {{!}} Pre-Init {{!}}0000000016{{!}} Physical Security Intrusion {{!}} General Chassis intrusion {{!}} Deasserted
			7 {{!}} Pre-Init {{!}}0000000011{{!}} Physical Security Intrusion {{!}} General Chassis intrusion {{!}} Asserted
			8 {{!}} Pre-Init {{!}}0000000016{{!}} Physical Security Intrusion {{!}} General Chassis intrusion {{!}} Deasserted
			9 {{!}} 06/11/2020 {{!}} 08:40:21 {{!}} Voltage CMOS Battery {{!}} Lower Critical going low {{!}} Asserted {{!}} Reading 2.57 < Threshold 2.64 Volts
			a {{!}} 06/11/2020 {{!}} 08:41:41 {{!}} Voltage CMOS Battery {{!}} Lower Critical going low {{!}} Deasserted {{!}} Reading 2.73 < Threshold 2.64 Volts
			b {{!}} 06/13/2020 {{!}} 19:01:06 {{!}} Voltage CMOS Battery {{!}} Lower Critical going low {{!}} Asserted {{!}} Reading 2.63 < Threshold 2.64 Volts
			c {{!}} 06/13/2020 {{!}} 19:01:11 {{!}} Voltage CMOS Battery {{!}} Lower Critical going low {{!}} Deasserted {{!}} Reading 2.68 < Threshold 2.64 Volts
			\| lang = terminal
			}}

			===Clearing System Event Log===
	Run {{code\|ipmitool sel clear}} to clear all SEL logs. This is useful if your machine has an amber light due to a machine check which you wish to clear.		Run {{code\|ipmitool sel clear}} to clear all SEL logs. This is useful if your machine has an amber light due to a machine check which you wish to clear.

	=== Polling Data ===		===Polling Data===
	Poll the data from iLO by running {{code\|ipmitool}}. An example output is given below.		Poll the data from iLO by running {{code\|ipmitool}}. An example output is given below.

Line 68:		Line 90:
	The data can be parsed then pushed into a logging server.		The data can be parsed then pushed into a logging server.

	== Troubleshooting ==		==Troubleshooting==
	{{highlight\|lang=terminal\|code=		{{highlight\|lang=terminal\|code=
	$ autoconf		$ autoconf
Line 83:		Line 105:
	}}		}}

	{{Navbox Linux}}[[Category:Linux]]		{{Navbox Linux}}
			[[Category:Linux]]
	[[Category:LinuxUtilities]]		[[Category:LinuxUtilities]]

Leo: Added categories

2020-06-14T23:52:50Z

Added categories

← Older revision		Revision as of 23:52, 14 June 2020
Line 82:		Line 82:
	$ autoreconf -i		$ autoreconf -i
	}}		}}

			{{Navbox Linux}}[[Category:Linux]]
			[[Category:LinuxUtilities]]

Leo at 00:20, 5 March 2020

2020-03-05T00:20:50Z

← Older revision		Revision as of 00:20, 5 March 2020
Line 1:		Line 1:
	{{code\|ipmitool}} is a utility to fetch information from devices that support the Intelligent Platform Management Interface. This includes servers such as the HP Proliant DL380 G6 which I have at home.		{{code\|ipmitool}} is a utility to fetch information from devices that support the Intelligent Platform Management Interface (IPMI). This includes servers such as the HP Proliant DL380 G6 which I have at home or practically all Dell servers.

	The project can be found at:		The project can be found at:

Leo: /* Usage */

2020-03-05T00:19:42Z

Usage

← Older revision		Revision as of 00:19, 5 March 2020
Line 11:		Line 11:

	== Usage ==		== Usage ==
			=== Clearing System Event Log ===
			Run {{code\|ipmitool sel clear}} to clear all SEL logs. This is useful if your machine has an amber light due to a machine check which you wish to clear.

			=== Polling Data ===
	Poll the data from iLO by running {{code\|ipmitool}}. An example output is given below.		Poll the data from iLO by running {{code\|ipmitool}}. An example output is given below.

Leo: /* Usage */

2019-01-08T02:02:25Z

Usage

Show changes