Gosund KS602 - Revision history

Leo at 01:14, 21 November 2022

2022-11-21T01:14:10Z

← Older revision		Revision as of 01:14, 21 November 2022
Line 7:		Line 7:
	All the pins you need to flash Tasmota are exposed as a test pad. Use some test clips to attach to 3v3, GND, TX, RX, and IO0 and flash Tasmota using esptool.		All the pins you need to flash Tasmota are exposed as a test pad. Use some test clips to attach to 3v3, GND, TX, RX, and IO0 and flash Tasmota using esptool.

	To get into programming mode, short IO0 to GND. Using a 10K resistor won't work!		To get into programming mode, short IO0 to GND. Using a 10K resistor to GND won't work!

	=== Configuration ===		=== Configuration ===

Leo at 01:08, 21 November 2022

2022-11-21T01:08:35Z

← Older revision		Revision as of 01:08, 21 November 2022
Line 2:		Line 2:
	The Gosund KS602 is a smart switch which I bought for around $28 CAD for two ($14 CAD each). It has a ESP8266 and can run Tasmota. The unit is very simple to open and easy to reflash with Tasmota.		The Gosund KS602 is a smart switch which I bought for around $28 CAD for two ($14 CAD each). It has a ESP8266 and can run Tasmota. The unit is very simple to open and easy to reflash with Tasmota.

	== Tasmota ~~configuration~~ ==		== Tasmota ==

			=== Flashing ===
			All the pins you need to flash Tasmota are exposed as a test pad. Use some test clips to attach to 3v3, GND, TX, RX, and IO0 and flash Tasmota using esptool.

			To get into programming mode, short IO0 to GND. Using a 10K resistor won't work!

			=== Configuration ===
	After flashing Tasmota, I had to configure my unit with the following template since the one on https://templates.blakadder.com/ did not work for me. This template will have the LEDs turn green when on and red when off.{{Highlight		After flashing Tasmota, I had to configure my unit with the following template since the one on https://templates.blakadder.com/ did not work for me. This template will have the LEDs turn green when on and red when off.{{Highlight
	\| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}		\| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}
Line 25:		Line 32:
	\|GPIO16		\|GPIO16
	\|<code>Led 3</code>		\|<code>Led 3</code>
	\|}{{Navbox Hardware}}		\|}

			== See also ==

			* https://tasmota.github.io/docs/devices/KS-602S-Switch/
			{{Navbox Hardware}}
	{{Navbox Tinkering}}		{{Navbox Tinkering}}
	[[Category:Tinkering]]		[[Category:Tinkering]]
	[[Category:Hardware]]		[[Category:Hardware]]

Leo at 06:38, 12 November 2022

2022-11-12T06:38:39Z

← Older revision		Revision as of 06:38, 12 November 2022
Line 2:		Line 2:
	The Gosund KS602 is a smart switch which I bought for around $28 CAD for two ($14 CAD each). It has a ESP8266 and can run Tasmota. The unit is very simple to open and easy to reflash with Tasmota.		The Gosund KS602 is a smart switch which I bought for around $28 CAD for two ($14 CAD each). It has a ESP8266 and can run Tasmota. The unit is very simple to open and easy to reflash with Tasmota.

	== ~~Configuration~~ ==		== Tasmota configuration ==
	After flashing Tasmota, I had to configure my unit with the following template since the one on https://templates.blakadder.com/ did not work for me. This template will have the LEDs turn green when on and red when off.{{Highlight		After flashing Tasmota, I had to configure my unit with the following template since the one on https://templates.blakadder.com/ did not work for me. This template will have the LEDs turn green when on and red when off.{{Highlight
	\| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}		\| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}
Line 8:		Line 8:
	}}		}}

	{{Navbox Hardware}}		=== Pinouts ===
			These are the pinouts that are defined. Everything that isn't specified is set to 'None'
			{\| class="wikitable"
			!Pin
			!Feature
			\|-
			\|GPIO0
			\|<code>Button 1</code>
			\|-
			\|GPIO2
			\|<code>Led_i 1</code>
			\|-
			\|GPIO14
			\|<code>Relay 1</code>
			\|-
			\|GPIO16
			\|<code>Led 3</code>
			\|}{{Navbox Hardware}}
	{{Navbox Tinkering}}		{{Navbox Tinkering}}
	[[Category:Tinkering]]		[[Category:Tinkering]]
	[[Category:Hardware]]		[[Category:Hardware]]

Leo: Added categories and navbox

2021-12-30T01:02:17Z

Added categories and navbox

← Older revision		Revision as of 01:02, 30 December 2021
Line 7:		Line 7:
	\| lang = terminal		\| lang = terminal
	}}		}}

			{{Navbox Hardware}}
			{{Navbox Tinkering}}
			[[Category:Tinkering]]
			[[Category:Hardware]]

Leo at 04:05, 10 June 2021

2021-06-10T04:05:12Z

← Older revision		Revision as of 04:05, 10 June 2021
Line 1:		Line 1:
	~~Configuration~~		[[File:Gosund KS602 Smart Plug Reflash.jpg\|alt=Gosund KS602 Smart Plug Reflash\|thumb\|Gosund KS602 Smart Plug Reflash]]
			The Gosund KS602 is a smart switch which I bought for around $28 CAD for two ($14 CAD each). It has a ESP8266 and can run Tasmota. The unit is very simple to open and easy to reflash with Tasmota.

	Tasmota template		== Configuration ==
			After flashing Tasmota, I had to configure my unit with the following template since the one on https://templates.blakadder.com/ did not work for me. This template will have the LEDs turn green when on and red when off.{{Highlight
	{{Highlight
	\| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}		\| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}
	\| lang = terminal		\| lang = terminal
	}}		}}

Leo: Created page with "Configuration Tasmota template {{Highlight | code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18} | lang = terminal }}"

2021-06-06T06:30:40Z

Created page with "Configuration Tasmota template {{Highlight | code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18} | lang = terminal }}"

New page

Configuration

Tasmota template

{{Highlight
| code = {"NAME":"Gosund KS-602","GPIO":[32,0,320,0,0,0,0,0,0,0,224,0,290,0],"FLAG":0,"BASE":18}
| lang = terminal
}}